
Nº 0085 · Chair
Panton Chair
One piece of plastic, from backrest to floor.
Why it matters
It is the first cantilever chair moulded in one piece of plastic, with no legs and no joints. Panton worked on it for more than a decade, and it was made in four different plastics before a version met his aim of an affordable chair.
Panton developed the form from his plywood S-chair of about 1956 and made a first model in 1960. He met Willi Fehlbaum of Vitra in 1963; a small series of 100 to 150 chairs in fibreglass-reinforced polyester followed in 1967, and series production in rigid polyurethane foam, for Herman Miller, began in 1968. Vitra has made it in polypropylene since 1999. The chair in this photograph is at the Milwaukee Art Museum.
What to notice
- The S-curveOne curve runs from the back through the seat to the floor, with no legs.
- The baseThe lower part sweeps back under the seat, leaving room for the feet and holding the seat out.
- The rolled rimA rolled rim runs along the edge, from the top of the back round the seat and down to the base.
3 min read
The full story
From plywood to plastic
Verner Panton had been trying to make a chair from a single piece of material since his student years around 1950. By 1956 he had one in moulded plywood, the S-chair, made by the Sommer company and sold by Thonet as models 275 and 276. It was too costly to make in numbers. The new plastics promised more freedom, and Panton began reworking the shape, above all by sweeping the base back to give the sitter room for legs and feet.
In this story
- From plywood to plastic
- Thirty minutes a chair
- The Luran S years
- A fourth plastic
- Materials
- Lacquered rigid polyurethane foam (1968 series)
- Dimensions
- About 82 × 49 × 55 cm
- Maker
- Vitra, at first for Herman Miller
- In collection
- V&A · Vitra Design Museum · NGV · Boijmans
- Status
- Real · made in polypropylene today
Connections
- Verner Panton
- Vitra
- Herman Miller
- Space Age
- Furniture design
- Polyurethane foam
- Plastic
- Weil am Rhein
Nearby in the archive
Tulip ChairSaarinen · 1956 · no legs either, but a stem
Up 5Pesce · 1969 · foam furniture of the same years
In collections
Go further
- Verner Panton: The Collected Works, Alexander von Vegesack and Mathias Remmele (eds.), Vitra Design Museum (2000)The catalogue of Panton’s whole output, with Mathias Remmele’s chapter on the chair, the account most museum records rely on.
- Panton Chair, CIRC.74-1969, Victoria and Albert MuseumThe record for a 1968 foam chair, with a long history of the design and each change of plastic.
- Panton Chair, MPA-1002-01, Vitra Design MuseumThe museum’s record for an early lacquered foam chair, linked to its prototypes and experimental models.
- Panton Chair, Verner Panton Design AGThe estate’s page, which lists every production version by year, material and maker.
- Monobloc: A Chair for the World, Vitra Design Museum (2017)The page for the 2017 exhibition that set the Panton Chair beside the cheap one-piece plastic chairs that came after it.
Sources
- Panton Chair, CIRC.74-1969, Victoria and Albert Museum
- Panton Chair, MPA-1002-01, Vitra Design Museum
- Panton chair, V 2325 (KN&V), Museum Boijmans Van Beuningen
- Panton Chair, D233-1973, National Gallery of Victoria
- Panton Chair Classic, Verner Panton Design

